山东提供随车吊折臂吊图片价格HCS160A-4随车吊的生产厂家

使用微信扫描二维码分享朋友圈，成交更快更简单！

山东提供随车吊折臂吊图片价格HCS160A-4随车吊的生产厂家

HCS 160a-4 product specification
Ix. Product technical parameters
Product model hcs160a-4
Maximum lifting moment (kn.m) 160
Maximum lifting weight (kg) 6300
Boom expansion joint number 4
Maximum working range (m) 11.1
Maximum lifting height (m) 12.5(from the crane mounting surface)
Luffing Angle (1 or 75 °)
(360 °) for the turning Angle of rotary
The rotary speed is 1r/min
Rated working pressure (MPa) 20
Rated flow rate (L/min) 50
Crane dead weight (kg) 2480
The total weight of the equipped chassis is 12t~25t
X product configuration
19. Four lifting arms and three telescopic arms.
20. Mechanical travel valve.
21. Single speed hydraulic winch, turbine-worm rotary reducer.
22. Standard 50 gear pump. (if no oil pump option is required, default left turn)
23. All-inclusive square cavity supporting legs, long span of 5300mm.
24. Manual proportional valve is optional.
25. It is recommended to equip single-chamber telescopic rear support legs (purchased separately, not included in the crane).
X. product advantages
14. The boom is made of Q690 high-strength steel plate with four pieces of welded together. The hexagon section greatly improves the boom strength compared with the first-generation products.
15. Large scope of work and wide scope of adaptation;
16. Telescopic crane boom as twin + zip form, when more than 20 ° Angle, oil cylinder part is rated load expansion ability, zip part is two-thirds load rating scale ability;
17. The hoisting machine adopts hydraulic winch, and the hoisting and releasing speed of the hook is 10m/min, with high speed, low noise, high efficiency and good reliability;
18. The maximum span of the supporting leg is 5.3m, which is greater than the span of the supporting leg of domestic products of the same tonnage.HCS160A-4产品技术说明书
山东济宁 随车吊 吊机
九、 产品技术参数
产品型号 HCS160A-4
大起重力矩（kN.m） 160
大起重量 (kg) 6300
吊臂伸缩节数 4
大工作幅度 (m) 11.1
大起升高度(m) 12.5(距起重机安装面)
变幅角度(°) 1～75
回转角度(°) 360全回转
回转速度 1r/min
额定工作压力(MPa) 20
额定流量(L/min) 50
起重机自重(kg) 2480
配装底盘 总质量12t~25t
十产品配置
19. 四节吊臂，三节伸缩臂。
20. 机械式行程阀。
21. 单速液压绞车、涡轮蜗杆回转减速器。
22. 标配50齿轮泵。（如不提供油泵选项需求，默认左旋）
23. 全包方腔式支腿，大跨距5300mm。
24. 可选装手动比例阀。
25. 推荐配置单腔伸缩式后支腿（另行购买，不在吊机中）
十、 产品优势
14. 吊臂采用Q690高强钢板、四块板拼焊，六边形截面，吊臂强度较一代产品大幅提升，强度高、韧性好、自重轻；
15. 工作幅度大，适应范围广；
16. 吊臂伸缩采用双缸+拉锁形式，在20°以上仰角时，油缸部分具有带额定载荷伸缩能力，拉锁部分具有带三分之二额定载荷伸缩的能力；
17. 卷扬机构采用液压绞车，吊钩收放速度10m/min，速度快, 噪音小、、可靠性好；
18. 支腿大跨距5.3m，大于国内同吨位产品支腿跨距，安装在14吨及以上底盘上时，不配后支腿即可满足稳定性要求；</a>